CellarPro 1800XTS-ECX 220V 50 Hz – Through The Wall Cooling Unit #27252

$2,250.00

1745 BTU/h
Dimensions: Width 46″ , Depth 42″ , Height 27″
Ideal for small wine cellars and wine closets
A Self Contained , Through The Wall Wine Cooling Unit

SKU CPRO-27252 Categories 1800 Series, CellarPro, Self Contained Systems, Through The Wall Series Tags 220V, 24V Thermostat, Extreme Low Ambient, Wine Cabinet Cooling Unit, Wine Refrigeration

CellarPro 1800XTS 220V wall cooling system (P/N 27252). CellarPro 1800 Series engineered the 1800XTS 220V wall cooling system to maintain ideal temperature and humidity conditions in geographies that use 220V / 1 Phase power / 50 Hz.

All air-cooled refrigeration equipment requires fresh air intake to dissipate the heat generated by the cooling unit. The fresh air intake CANNOT come from the wine cellar space – it must come from space outside the cellar. Designed for indoor use, 1800XTS 220V units can operate in environments ranging from 35C to 4C out of the box. To operate the unit in colder temperatures, please see modifications listed on the Options & Upgrades tab.

On the hot side, this 1800 Series wall cooling system intakes from the rear, and offers a choice of top or rear hot exhaust.
On the cold side, this wall cooling system intakes from the front and exhausts from the bottom (thus the front 8 inches of the cooling unit must be inside the cellar.)
The 1800 Series cooling unit requires fresh air intake at the rear of the cooling unit. If sufficient space does not exist to provide sufficient airflow to the rear of the cooling unit, you may need a rear duct kit.
1800 Series cooling units can be installed completely inside the wine cellar when used with our rear duct kit, which allows you to duct the supply and return airflows from the rear of the cooling unit up to 100 equivalent feet (50 feet per duct).
Please note: The cold side of the 1800 Series cooling units cannot be ducted, and the hot side can be ducted with 6-inch ducting (no reductions) plus auxiliary fan support, which is included with our our rear duct kit.
You must located this 1800 Series cooling unit within the cellar, with the following exception: these units can be installed directly above the wine cellar when used with our front intake hood.
For installation in environments below 40F, our compressor heater modification is required.
For installation in environments below 20F down to -20F, we recommend our Fan-Cycling Switch (P/N 6972) combined with our compressor heater.
A CellarPro 1800 Series cooling unit must always be used in the upright position, and should never be operated on its side or upside down.

CellarPro 1800 XTS-ECX 220V wall cooling system (P/N 27252). CellarPro engineered the 1800XTS-ECX 220V wall cooling system to maintain ideal temperature and humidity conditions in geographies that use 220V / 1 Phase power / 50 Hz.

All air-cooled refrigeration equipment requires fresh air intake to dissipate the heat generated by the cooling unit. The fresh air intake CANNOT come from the wine cellar space – it must come from space outside the cellar. Designed for indoor use, 1800XTS-ECX 220V units can operate in environments ranging from 35C to 4C out of the box. To operate the unit in colder temperatures, please see the modifications listed on the Options & Upgrades tab.

Now with energy-efficient EC Fans on both the cold and hot sides, save $39.02 in annual energy costs vs AC fans (assumes 75% runtime and $0.15/kWh)
This 1800 Series cooling unit offers a choice of top or rear hot exhaust.
Adjustable humidity control combines a high-output compressor with flexible fan cycles to maintain a recommended level of moisture inside your cellar.
Extra-large coils generate maximum cooling power.
Commercial-grade Electrofin coating protects the evaporator coils from leaks and corrosion.
The intuitive LED display panel mounted on the evaporator with a digital programmable thermostat is simple and easy to use. The remote thermostat is available as an upgrade.
Energy-saver mode, quick-chill mode, and auto-defrost cycle provide convenient solutions to common cellar needs.
The temperature set point range is 8.3C to 16.7C when the cooling unit is properly sized.
The 1800 Series cooling unit operates with minimal vibrations and less noise (53 dBA @ 50Hz).
Audible and visual alarms and maintenance-needed indicators protect the cooling unit and the wine cellar.
The 8-foot power cord exits from the rear.
The removable steel case provides access to the internal components for servicing and repair.
CellarPro’s 2-Year Standard Warranty, the most thorough in the industry, protects the unit against manufacturing defects.

1745 SENSIBLE BTUH @ 50Hz/12.8C.
CellarPro 1800XTS-ECX 220V cooling units (1/6 Ton Nominal) provide outstanding performance, adjustable humidity control and extra cooling power for use in 220V/1PH/50-Hz environments. Now with energy-efficient EC fans.

This cooling unit cannot be used in 60 Hz environments (eg North America).

Our CellarPro 1800 XTS-ECX cooling unit is designed to be used in properly-constructed wine cellars that are adequately insulated, airtight and sealed with a vapor barrier. In improperly-constructed cellars, the cooling unit will create excess condensation, leading to damage and premature failure of your cooling unit (not covered by warranty).

The BTU/h value shown here is a theoretical number. There are often circumstances under which a cellar design may require a larger unit due to variables not accounted for in the formula. For example, these variables could be building materials (such as glass, stone, concrete, etc.)

Which do not offer the insulation capacity required to maintain the optimal cellar environment. We recommend purchasing a unit with a larger capacity to compensate for these unaccounted-for variables. An undersized unit can lead to premature failure and will most likely prevent the cellar from reaching your desired temperature.

Brand: CellarPro

Size: 46w x 42d x 27h (cm) (in)

Weight: 60 lbs

Power/Rating:
220V AC / 1PH / 50Hz
Compressor Amps:
– Running: 2.32 Amps
– Startup: 13.5 Amps
– Total Watts: 302

– Required: Dedicated 15-Amp Circuit
– Recommended: Surge Protector

This CellarPro 1800 XTS-ECX wine cooling unit can be used in 187-254V environments at 50Hz. The power plug provided is Nema 6-15P 15A 250V Plug (Male). It has a screw cover plug housing with internal lug connections and can be swapped easily to conform to local plug configurations

Capacity: 1745 BTUH @ 50Hz / 12.8C

Warranty Resources
– Warranty Overview

WARNING - This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Cold Temperature

Fan Cycling Switch #6972: supports the unit in temperatures below 20F and as low as -20F.

Duct Hoods

Duct Intake Hood (Cold Side) #1932: permits the cooling unit to be placed directly above the cellar.
Duct Hood (Hot Side) #7409: allows you to install the unit completely inside your cellar or in a small space with limited airflow. Includes an auxiliary fan, but no ducting.
Duct Kit (Hot Side) #1439: same as the Duct Hood, this kit also includes 2 x 25-feet of 6-inch insulated (R-6) flex ducting.

Filters & Grills

Use our filter & grill guide to find the cooling unit filter or duct filter and/or duct grill that is appropriate for your cooling unit.

Remote Control & Probe

Remote Display #1603: lets you place the digital panel wherever you want, whether inside or outside the cellar. Includes 10 feet of wiring.
Bottle Probe #1434: this remote thermostat with a 10-foot cord overrides the thermostat on the face of the cooling unit, and allows it to monitor air or liquid temperatures at various locations inside the cellar.
Extension cords available in 25-foot (#1780) and 50-foot (#1781) lengths.
Mounting Clips #1095: attached to the front of CellarPro 1800 Series cooling units, these clips are designed to be bolted to the ceiling inside the wine cabinet / cellar.

DID YOU KNOW?
Nobody protects your wine cellar better than CellarPro Cooling Systems! In the event your cooling unit fails and the failed components are covered by our warranty, we’ll send a replacement cooling unit to you per the terms of our Replacement Unit Program

CellarPro Replacement Unit Program
If your CellarPro cooling unit fails and the parts that failed are still covered by warranty, we’ll send a replacement cooling unit to you, as follows:

Your cooling unit must be registered at CellarPro
Your cooling unit must have been properly sized, installed and maintained
Your cooling unit may not have been permanently modified, damaged or disfigured

Please note:

Replacement units are factory-refurbished cooling units with a similar build date as your original unit
You are responsible for the shipping cost to send the replacement unit to you and return the original unit to us, and the cost (if any) to remove the original unit and install the replacement unit
In order to send a replacement unit, we require a deposit, which will be refunded minus shipping costs upon the return and pending the inspection of the original unit
If the original unit failed due to improper intallation or use, the failure is not covered by warranty and we will deduct the cost of the repairs from the refund of your deposit

– Owner’s Manual
– Product Brochure

Wine Cellar Installation Diagrams
– Rear Drawings – As Ducted
– Mounting Clips
– Shelf

Cooling Unit Replacement Instructions
– Replace Wine Cooling Units

Dimensions:
– Front, Rear & Side Views
– Top & Bottom View